Wi-Fi that reaches every meter and the devices behind them

Wi-Fi HaLow connects smart meters, the neighborhood around them, and the EV chargers, solar, batteries, and heat pumps inside the home, on one standards-based Wi-Fi network.

Wi-Fi HaLow connects the grid edge, from the neighborhood to in-home.

Distributed energy resources (DERs)

EV chargers, solar inverters, home batteries, heat pumps, and water heaters behind the meter, connected directly to the meter giving the utility visibility of the loads that shape the grid. Meters with Wi⁠-⁠Fi HaLow can reach devices wherever they are on the property.

Meter and neighborhood area networks

Meters connected to each other and to a take-out point at the transformer, with the bandwidth for firmware updates and edge applications across every home on the street.

Faster response to changing demand

Balance EV charging and rooftop solar at the transformer, shift or curtail loads during peaks, and push new applications to meters as demand grows, with the speed and bandwidth AMI 2.0 needs.

The visibility and response gap

EV chargers, heat pumps, rooftop solar, and home batteries now shape how much power a street draws or exports, and most of them sit behind the meter, out of the utility's view. Meter networks built for billing reads run at kbps rates, too slow for near real-time response. Cellular adds a subscription to every device, and home Wi-Fi sits outside the utility's control.

Wi-Fi HaLow closes the gap: sub-1 GHz reach from the meter into the home and across the neighborhood, with Mbps data rates and WPA3 security, alongside the meter's existing connection to the utility.

RF mesh
(proprietary, Wi-SUN)
Cellular
(LTE-M, NB-IoT)
Zigbee
Home Wi-Fi
(Wi-Fi 4, 2.4 GHz)
Range
Long range per hop, extended by multi-hop mesh
Wide-area, carrier dependent
Short
(tens of meters per hop)
Short
(tens of meters indoors)
Material penetration
Strong
Strong on low bands,
at reduced data rates
Limited
Limited
Reach behind the meter
Limited (relies on a separate home radio)
Per device, dependent on carrier coverage
Short range; the meter's home radio often can't reach the garage or roof
Customer-owned; often drops out in garages, attics, and utility rooms
Data rates and speed
Up to 300 kbps
(Wi-SUN FAN 1.0);
up to 2.4 Mbps (FAN 1.1)
Tens of kbps (NB-IoT) to about 1 Mbps (LTE-M)
Up to 250 kbps
Up to 72 Mbps (typical single-stream 2.4 GHz Wi⁠-⁠Fi in IoT devices.)
Devices per network
Thousands per collector, relayed meter to meter
One SIM per device;
no local network
Hundreds per coordinator (mesh), limited by range and congestion
Dozens per access point, limited by range and congestion
Ongoing costs
None
Subscription per device; carrier decides price and network lifespan
None
None,
but outside utility control
Swipe the table to compare all technologies →
* PHY rate with 8 MHz channels, where regional rules permit (US, Canada, Australia). EU deployments under EN 304 220 use 1 MHz channels at lower rates.

The grid needs faster data from every meter and the devices behind it

First-generation smart meters report usage a few times a day. This was enough for billing and outage alerts, but not for managing a grid with growing solar, battery, and EV load.

AMI 2.0 meters run applications at the grid edge, from fault and transformer-load detection to DER visibility, and need near real-time data to deliver them. Wi-Fi HaLow gives those meters the bandwidth and the reach into the home, alongside their existing connection to the utility.

CAPABILITIES

What Wi-Fi HaLow delivers for energy management

Whole-home reach from the meter

Sub-1 GHz signal reaches the garage, roof, and basement, with no extenders.

Bandwidth for AMI 2.0

Mbps data rates for firmware updates, edge applications, and near real-time data.

One radio, two networks

Meter to meter across the neighborhood, and meter to device inside the home.

Keep local traffic local

Meters under one transformer share data locally, easing backhaul load and cellular costs.

Built in or added on

Design Wi-Fi HaLow into new meters, or add through swappable RF modules where meters allow.

Open, secure, self-deployed

WPA3 and native IP, carrying energy protocols like IEEE 2030.5, with no vendor lock-in.

One network, from the meter into the home

Meters, the neighborhood around them, and the energy devices behind them, all on one secure network. Visibility at the grid edge, without a separate network for each layer.

Built and backed by the Wi⁠-⁠Fi we all know and trust.

Defined by the IEEE

Wi-Fi HaLow is based on the 802.11ah standard, defined by the Institute of Electrical and Electronics Engineers (IEEE), the same body behind every generation of Wi-Fi.

Certified by the Wi-Fi Alliance

Wi-Fi CERTIFIED HaLow is certified by the Wi-Fi Alliance, the global industry association that promotes interoperability, security, and consistent performance across Wi-Fi products.

Tested by Morse Micro

As a Wi-Fi Alliance approved Wi-Fi HaLow testbed vendor, Morse Micro helps companies test, validate and refine their Wi-Fi HaLow products in preparation for certification.

morse Micro products

Building with Wi-Fi HaLow

Whether you’re looking to build our chips or modules into your next product, testing with our eval kits and reference designs, or looking for a finished product to take to market, we have a Wi-Fi HaLow option for every stage.

Products Overview
1/6

Chips

Single-chip 802.11ah SoCs for OEMs building Wi-Fi HaLow hardware from the silicon up.

Small microchip circuit module on a purple printed circuit board background.

Modules

Pre-certified, drop-in modules that add Wi-Fi HaLow without the RF engineering.

Purple circuit boards with electronic components and labels on a printed circuit background.

Development Resources

Plug-and-play kits to test range, throughput and power in your own environment.

End Products

Selection of products with Morse Micro's Wi-Fi HaLow technology within.